[Federal Register: January 15, 1998 (Rules and Regulations)]
[Page 2551-2555]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr15ja98-14]

[[pp. 2551-2555]] Implementation of the Wassenaar Arrangement List of Dual-Use
Items: Revisions to the Commerce Control List and Reporting Under the
Wassenaar Arrangement

[[Continued from page 2550]]

[[Page 2551]]

9B105  Wind tunnels for speeds of Mach 0.9 or more, usable for
``missiles'' and their subsystems.

License Requirements

Reason for Control: MT, AT


               Control(s)                         Country Chart

MT applies to entire entry.............  MT Column 1
AT applies to entire entry.............  AT Column 1


License Exceptions
LVS: N/A
GBS: N/A
CIV: N/A

List of Items Controlled

Unit: $ value
Related Controls: See also 9B005
Related Definitions: N/A
Items: The list of items controlled is contained in the ECCN heading

9B106  Environmental chambers and anechoic chambers, as follows (see
List of Items Controlled).

License Requirements

Reason for Control: MT, AT


               Control(s)                         Country Chart

MT applies to entire entry.............  MT Column 1
AT applies to entire entry.............  AT Column 1


License Exceptions

LVS: N/A
GBS: N/A
CIV: N/A

List of Items Controlled

Unit: $ value
Related Controls: N/A
Related Definitions: N/A
Items: a. Environmental chambers capable of simulating the following
flight conditions:
    a.1. Altitudes of 15,000 m or greater; or
    a.2. Temperature of at least 223 K (-50 deg. C) to 398 K (+
125 deg. C) and vibration environments of 10 g rms or greater
between 20 Hz and 2,000 Hz and imparting forces of 5 Kn or greater.
    b. Anechoic chambers capable of simulating the following flight
conditions:
    b.1. Altitudes of 15,000 m or greater; or
    b.2. Temperature of at least 223 K (50 deg. C) to 398 K (+
125 deg. C) and acoustic environments at an overall sound pressure
level of 140 Db or greater (referenced to 20 microPa) or with a
rated power output of 4 kW or greater.

9B115  Specially designed ``production equipment'' for the systems,
sub-systems and components controlled by 9A005 to 9A009, 9A011,
9A101, 9A105 to 9A109, 9A111, 9A116 to 9A119. (These items are
subject to the export licensing authority of the U.S. Department of
State, Office of Defense Trade Controls. See 22 CFR part 121.)

9B116  Specially designed ``production facilities'' for the systems,
sub-systems, and components controlled by 9A004 to 9A009, 9A011,
9A101, 9A104 to 9A109, 9A111, 9A116 to 9A119. (These items are
subject to the export licensing authority of the U.S. Department of
State, Office of Defense Trade Controls. See 22 CFR part 121.)

9B117  Test benches and test stands for solid or liquid propellant
rockets or rocket motors, having either of the following
characteristics (see List of Items Controlled).

License Requirements

Reason for Control: MT, AT


               Control(s)                         Country Chart

MT applies to entire entry.............  MT Column 1
AT applies to entire entry.............  AT Column 1


License Exceptions

LVS: N/A
GBS: N/A
CIV: N/A

List of Items Controlled

Unit: $ value
Related Controls: See also 9B990
Related Definitions: N/A
Items: a. The capacity to handle more than 90 Kn of thrust; or
    b. Capable of simultaneously measuring the three axial thrust
components.

9B990  Vibration test equipment and specially designed parts and
components, n.e.s.

License Requirements

Reason for Control: AT


               Control(s)                         Country Chart

AT applies to entire entry.............  AT Column 1


License Exceptions

LVS: N/A
GBS: N/A
CIV: N/A

List of Items Controlled

Unit: $ value
Related Controls: N/A
Related Definitions: N/A
Items: The list of items controlled is contained in the ECCN heading

9B991  Specially designed equipment, tooling or fixtures, not
controlled by 9B001, as described in the List of Items Controlled, for
manufacturing or measuring gas turbine blades, vanes or tip shroud
castings.

License Requirements

Reason for Control: AT


               Control(s)                         Country Chart

AT applies to entire entry.............  AT Column 1


License Exceptions

LVS: N/A
GBS: N/A
CIV: N/A

List of Items Controlled

Unit: $ value
Related Controls: N/A
Related Definitions: N/A
Items: a. Automated equipment using non-mechanical methods for
measuring airfoil wall thickness;
    b. Tooling, fixtures or measuring equipment for the ``laser'',
water jet or ECM/EDM hole drilling processes controlled by 9E003.c;
    c. Ceramic core leaching equipment;
    d. Ceramic shell burn out or firing equipment.

C. Materials [Reserved]

D. Software

9D001  ``Software'' required for the ``development'' of equipment or
``technology'' controlled by 9A (except 9A018, 9A990 or 9A991), 9B
(except 9B990 or 9B991) or 9E003.

License Requirements

Reason for Control: NS, MT, AT


               Control(s)                         Country Chart

NS applies to ``software'' for items     NS Column 1
 controlled by 9A001 to 9A003, 9B001 to
 9B009, 9E003.
MT applies to ``software'' for           MT Column 1
 equipment controlled by 9A001, 9A101,
 9A106, 9A110, 9A120, 9B001, 9B002,
 9B003, 9B004, 9B005, 9B007, 9B105,
 9B106, 9B116, and 9B117 for MT reasons.
AT applies to entire entry.............  AT Column 1


    License Requirement Notes: See Sec. 743.1 of the EAR for
reporting requirements for exports under License Exceptions.

License Exceptions

CIV: N/A
TSR: N/A

List of Items Controlled

Unit: $ value
Related Controls: (1) See also 9D101. (2) ``Software'' ``required''
for the ``development'' of items controlled by 9A004 is subject to
the export licensing authority of the U.S. Department of State,
Office of Defense Trade Controls. (See 22 CFR part 121.) (3)
``Software'' ``required'' for the ``development'' of equipment or
``technology'' subject to the export licensing authority of the U.S.
Department of State, Office of Defense Trade Controls is also
subject to the same licensing jurisdiction. (See 22 CFR part 121.)
Related Definitions: N/A
Items: The list of items controlled is contained in the ECCN heading

9D002  ``Software'' required for the ``production'' of equipment
controlled by 9A (except 9A018, 9A990 or 9A991) or 9B (except 9B990 or
9B991).

License Requirements

Reason for Control: NS, MT, AT

[[Page 2552]]


               Control(s)                         Country Chart

NS applies to ``software'' for           NS Column 1
 equipment controlled by 9A001 to 9A003
 or 9B001 to 9B009.
MT applies to ``software'' for           MT Column 1
 equipment controlled by 9A001, 9A101,
 9A106, 9A110, 9A120, 9B001, 9B002,
 9B003, 9B004, 9B005, 9B007 9B105,
 9B106, 9B116, and 9B117 for MT reasons.
AT applies to entire entry.............  AT Column 1


    License Requirement Notes: See Sec. 743.1 of the EAR for
reporting requirements for exports under License Exceptions.

License Exceptions

CIV: N/A
TSR: N/A

List of Items Controlled

Unit: $ value
Related Controls: (1) ``Software'' ``required'' for the
``production'' of items controlled by 9A004 is subject to the export
licensing authority of the U.S. Department of State, Office of
Defense Trade Controls. (See 22 CFR part 121.) (2) ``Software''
``required'' for the ``production'' of equipment or ``technology''
subject to the export licensing authority of the U.S. Department of
State, Office of Defense Trade Controls is also subject to the same
licensing jurisdiction. (See 22 CFR part 121.)
Related Definitions: N/A
Items: The list of items controlled is contained in the ECCN heading

9D003  ``Software'' required for the ``use'' of full authority digital
electronic engine controls (FADEC) for propulsion systems controlled by
9A (except 9A018, 9A990 or 9A991) or equipment controlled by 9B (except
9B990 or 9B991), as follows (see List of Items Controlled).

License Requirements

Reason for Control: NS, MT, AT


               Control(s)                         Country Chart

NS applies to ``software'' for ``use''   NS Column 1
 of FADEC for equipment controlled by
 9A001 to 9A003.
MT applies to ``software'' required for  MT Column 1
 the ``use'' of FADEC for gas turbine
 engines controlled by 9A101, 9A106, or
 9A110.
AT applies to entire entry.............  AT Column 1


License Exceptions

CIV: Yes, except N/A for MT
TSR: Yes, except N/A for MT

List of Items Controlled

Unit: $ value
Related Controls: (1) See also 9D103. (2) ``Software'' ``required''
for the ``use'' of items controlled by 9A004 is subject to the
export licensing authority of the U.S. Department of State, Office
of Defense Trade Controls. (See 22 CFR part 121.) (3) ``Software''
``required'' for the ``use'' of equipment or ``technology'' subject
to the export licensing authority of the U.S. Department of State,
Office of Defense Trade Controls is also subject to the same
licensing jurisdiction. (See 22 CFR part 121.)
Related Definitions: N/A
Items: a. ``Software'' in digital electronic controls for propulsion
systems, aerospace test facilities or air breathing aero-engine test
facilities;
    b. Fault-tolerant ``software'' used in ``FADEC'' systems for
propulsion systems and associated test facilities.

9D004  Other ``software'', as follows (see List of Items Controlled).

License Requirements

Reason for Control: NS, MT, AT


               Control(s)                         Country Chart

NS applies to entire entry.............  NS Column 1
MT applies to entire entry.............  MT Column 1
AT applies to entire entry.............  AT Column 1


License Exceptions

CIV: N/A
TSR: N/A

List of Items Controlled

Unit: $ value
Related Controls: N/A
Related Definitions: N/A
Items: a. 2D or 3D viscous ``software'' validated with wind tunnel
or flight test data required for detailed engine flow modelling;
    b. ``Software'' for testing aero gas turbine engines, assemblies
or components, specially designed to collect, reduce and analyze
data in real time, and capable of feedback control, including the
dynamic adjustment of test articles or test conditions, as the test
is in progress;
    c. ``Software'' specially designed to control directional
solidification or single crystal casting;
    d. ``Software'' in ``source code'', ``object code'' or machine
code required for the ``use'' of active compensating systems for
rotor blade tip clearance control.

    Note: 9D004.d does not control ``software'' embedded in
uncontrolled equipment or required for maintenance activities
associated with the calibration or repair or updates to the active
compensating clearance control system.

9D018  ``Software'' for the ``use'' of equipment controlled by 9A018.

License Requirements

Reason for Control: NS, RS, AT


               Control(s)                         Country Chart

NS applies to entire entry.............  NS Column 1
RS applies to 9A018.a and .b...........  RS Column 2
AT applies to entire entry.............  AT Column 1


License Exceptions

CIV: N/A
TSR: Yes for Australia, Japan, New Zealand, and NATO only

List of Items Controlled

Unit: $ value
Related Controls: N/A
Related Definitions: N/A
Items: The list of items controlled is contained in the ECCN heading

9D101  ``Software'' specially designed for the ``use'' of goods
controlled by 9B105, 9B106, 9B116 or 9B117.

License Requirements

Reason for Control: MT, AT


               Control(s)                         Country Chart

MT applies to entire entry.............  MT Column 1
AT applies to entire entry.............  AT Column 1


License Exceptions

CIV: N/A
TSR: N/A

List of Items Controlled

Unit: $ value
Related Controls: N/A
Related Definitions: N/A
Items: The list of items controlled is contained in the ECCN heading

9D102  ``Software'' specially designed for the ``use'' of items
controlled by 9A101, 9A106, 9A110, and 9A120.

License Requirements

Reason for Control: MT, AT


               Control(s)                         Country Chart

MT applies to entire entry.............  MT Column 1
AT applies to entire entry.............  AT Column 1


License Exceptions

CIV: N/A
TSR: N/A

List of Items Controlled

Unit: $ value
Related Controls: ``Software'' for items controlled by 9A115 are
subject to the export licensing authority of the U.S. Department of
State, Office of Defense Trade Controls (see 22 CFR part 121)
Related Definitions: N/A
Items: The list of items controlled is contained in the ECCN heading

9D103  ``Software'' specially designed for modelling, simulation or
design integration of ``missiles'', or the subsystems controlled by
9A005, 9A007, 9A105.a, 9A106, 9A108, 9A116 or 9A119. (This entry is
subject to the export licensing authority of the U.S. Department of
State, Office of Defense Trade Controls. See 22 CFR part 121.)

9D990  ``Software'', n.e.s., for the ``development'' or ``production''
of equipment controlled by 9A990 or 9B990.

License Requirements

Reason for Control: AT


               Control(s)                         Country Chart

AT applies to ``software'' for           AT Column 1
 equipment under 9A990 except 9A990.a.

[[Page 2553]]


AT applies to ``software'' for           AT Column 2
 equipment under 9A990.a only.


License Exceptions

CIV: N/A
TSR: N/A

List of Items Controlled

Unit: $ value
Related Controls: N/A
Related Definitions: N/A
Items: The list of items controlled is contained in the ECCN heading

9D991  ``Software'', for the ``development'' or ``production'' of
equipment controlled by 9A991 or 9B991.

License Requirements

Reason for Control: AT


               Control(s)                         Country Chart

AT applies to entire entry.............  AT Column 1


License Exceptions

CIV: N/A
TSR: N/A

List of Items Controlled

Unit: $ value
Related Controls: N/A
Related Definitions: N/A
Items: The list of items controlled is contained in the ECCN heading

E. Technology

    Note: ``Development'' or ``production'' ``technology''
controlled by 9E001 to 9E003 for gas turbine engines remains
controlled when used as ``use'' ``technology'' for repair, rebuild
and overhaul. Excluded from control are: technical data, drawings or
documentation for maintenance activities directly associated with
calibration, removal or replacement of damaged or unserviceable line
replaceable units, including replacement of whole engines or engine
modules.

9E001   ``Technology'' according to the General Technology Note for the
``development'' of equipment or ``software'' controlled by 9A001.c,
9A004 to 9A011, 9B (except 9B990 or 9B991), or 9D (except 9D990 or
9D991).

License Requirements

Reason for Control: NS, MT, AT


               Control(s)                         Country Chart

NS applies to ``technology'' for items   NS Column 1
 controlled by 9A001.c, 9B001 to 9B009,
 9D001 to 9D004.
MT applies to ``technology'' for items   MT Column 1
 controlled by 9B001, 9B002, 9B003,
 9B004 9B005, 9B007, 9B105, 9B106,
 9B116, 9B117, 9D001, 9D002, 9D003, and
 9D004 for MT reasons.
AT applies to entire entry.............  AT Column 1


    License Requirement Notes: See Sec. 743.1 of the EAR for
reporting requirements for exports under License Exceptions.

License Exceptions

CIV: N/A
TSR: N/A

List of Items Controlled

Unit: N/A
Related Controls: (1) See also 9E101 and 1E002.f (for controls on
``technology'' for the repair of controlled structures, laminates or
materials). (2) The ``technology'' required for the ``development''
of equipment controlled by 9A004 is subject to the export licensing
authority of the U.S. Department of State, Office of Defense Trade
Controls. (See 22 CFR part 121.) (3) ``Technology'', required for
the ``development'' of equipment or ``software'' subject to the
export licensing authority of the U.S. Department of State, Office
of Defense Trade Controls, is also subject to the same licensing
jurisdiction. (See 22 CFR part 121)
Related Definitions: ``Development'' or ``production''
``technology'' controlled by 9E for gas turbine engines remains
controlled when used as ``use'' ``technology'' for repair, rebuild
and overhaul. Excluded from control are: technology, drawings or
documentation for maintenance activities directly associated with
calibration, removal or replacement of damaged or unserviceable line
replaceable units, including replacement of whole engines or engine
modules
Items: The list of items controlled is contained in the ECCN heading

9E002   ``Technology'' according to the General Technology Note for the
``production'' of equipment controlled by 9A001.c, 9A004 to 9A011 or 9B
(except 9B990 or 9B991).

License Requirements

Reason for Control: NS, MT, AT


               Control(s)                         Country Chart

NS applies to entire entry.............  NS Column 1
MT applies to ``technology'' for         MT Column 1
 equipment controlled by 9B001, 9B002,
 9B003, 9B004, 9B005, 9B007, 9B105,
 9B106, 9B116, and 9B117 for MT reasons.
AT applies to entire entry.............  AT Column 1


    License Requirement Notes: See Sec. 743.1 of the EAR for
reporting requirements for exports under License Exceptions.

License Exceptions

CIV: N/A
TSR: N/A

List of Items Controlled

Unit: N/A
Related Controls: (1) See also 9E102. (2) The ``technology''
required for the ``development'' of equipment controlled by 9A004 is
subject to the export licensing authority of the U.S. Department of
State, Office of Defense Trade Controls. (See 22 CFR part 121.) (3)
``Technology'', required for the ``development'' of equipment or
``software'' subject to the export licensing authority of the U.S.
Department of State, Office of Defense Trade Controls, is also
subject to the same licensing jurisdiction. (See 22 CFR part 121)
Related Definitions: N/A
Items: The list of items controlled is contained in the ECCN heading

9E003   Other ``technology'', as follows (see List of Items
Controlled).

License Requirements

Reason for Control: NS, SI, AT


               Control(s)                         Country Chart

NS applies to entire entry.............  NS Column 1
SI applies to 9E003.a.1 through a.12 and f. See Sec.  742.14 of the EAR
 for additional information..
AT applies to entire entry.............  AT Column 1


    License Requirement Notes: See Sec. 743.1 of the EAR for
reporting requirements for exports under License Exceptions

License Exceptions

CIV: N/A
TSR: N/A
List of Items Controlled

Unit: N/A
Related Controls: (1) Hot section ``technology'' specifically
designed, modified, or equipped for military uses or purposes, or
developed principally with U.S. Department of Defense funding, is
subject to the licensing authority of the U.S. Department of State.
(2) ``Technology'' is subject to the EAR when actually applied to a
commercial aircraft engine program. Exporters may seek to establish
commercial application either on a case-by-case basis through
submission of documentation demonstrating application to a
commercial program in requesting an export license from the
Department Commerce in respect to a specific export, or in the case
of use for broad categories of aircraft, engines, or components, a
commodity jurisdiction determination from the Department of State.
Related Definitions: N/A

Items: a. ``Technology'' ``required'' for the ``development'',
``production'', or overhaul of the following commercial aircraft
engines, components or systems:
    a.1. Gas turbine blades, vanes or tip shrouds made from
directionally solidified (DS) or single crystal (SC) alloys having
(in the 001 Miller Index Direction) a stress-rupture life exceeding
400 hours at 1,273 K (1,000 deg. C) at a stress of 200 MPa, based on
the average property values;
    a.2. Multiple domed combustors operating at average burner
outlet temperatures exceeding 1,643 K (1,370 deg. C) or combustors
incorporating thermally decoupled combustion liners, non-metallic
liners or non-metallic shells;
    a.3. Components manufactured from organic ``composite''
materials designed to operate above 588 K (315 deg. C), or from
metal ``matrix'' ``composite'', ceramic ``matrix'', intermetallic or
intermetallic reinforced materials controlled by 1A002 or 1C007;
    a.4. Uncooled turbine blades, vanes, tip-shrouds or other
components designed to

[[Page 2554]]

operate at gas path temperatures of 1,323 K (1,050 deg. C) or more;
    a.5. Cooled turbine blades, vanes or tip-shrouds, other than
those described in 9E003.a.1, exposed to gas path temperatures of
1,643 K (1,370 deg.C) or more;
    a.6. Airfoil-to-disk blade combinations using solid state
joining;
    a.7. Gas turbine engine components using ``diffusion bonding''
``technology'' controlled by 2E003.b;
    a.8. Damage tolerant gas turbine engine rotating components
using powder metallurgy materials controlled by 1C002.b;
    a.9. Full authority digital electronic engine control (FADEC)
for gas turbine and combined cycle engines and their related
diagnostic components, sensors and specially designed components;
    a.10. Adjustable flow path geometry and associated control
systems for:
    a.10.a. Gas generator turbines;
    a.10.b. Fan or power turbines;
    a.10.c. Propelling nozzles;

    Notes: 1. Adjustable flow path geometry and associated control
systems do not include inlet guide vanes, variable pitch fans,
variable stators or bleed valves for compressors.
    2. 9E003.a.10 does not control ``development'' or ``production''
``technology'' for adjustable flow path geometry for reverse thrust.

    a.11. Rotor blade tip clearance control systems employing active
compensating casing ``technology'' limited to a design and
development data base; or
    a.12 Gas bearing for gas turbine engine rotor assemblies;
    a.13. Wide chord hollow fan blades without part-span support;
    b. ``Technology'' ``required'' for the ``development'' or
``production'' of any of the following:
    b.1. Wind tunnel aero-models equipped with non-intrusive sensors
capable of transmitting data from the sensors to the data
acquisition system; or
    b.2. ``Composite'' propeller blades or propfans capable of
absorbing more than 2,000 kW at flight speeds exceeding Mach 0.55;
    c. ``Technology'' ``required'' for the ``development'' or
``production'' of gas turbine engine components using ``laser'',
water jet, ECM or EDM hole drilling processes to produce holes
having any of the following sets of characteristics:
    c.1. All of the following:
    c.1.a. Depths more than four times their diameter;
    c.1.b. Diameters less than 0.76 mm; and
    c.1.c. Incidence angles equal to or less than 25 deg.; or
    c.2. All of the following:
    c.2.a. Depths more than five times their diameter;
    c.2.b. Diameters less than 0.4 mm; and
    c.2.c. Incidence angles of more than 25 deg.;

    Technical Note: For the purposes of 9E003.c, incidence angle is
measured from a plane tangential to the airfoil surface at the point
where the hole axis enters the airfoil surface.

    d. ``Technology'' ``required'' for the ``development'' or
``production'' of helicopter power transfer systems or tilt rotor or
tilt wing ``aircraft'' power transfer systems:
    d.1. Capable of loss-of-lubrication operation for 30 minutes or
more; or
    d.2. Having an input power-to-weight ratio equal to or more than
8.87 kW/kg;
    e.1. ``Technology'' for the ``development'' or ``production'' of
reciprocating diesel engine ground vehicle propulsion systems having
all of the following:
    e.1.a. A box volume of 1.2 m\3\ or less;
    e.1.b. An overall power output of more than 750 kW based on 80/
1269/EEC, ISO 2534 or national equivalents; and
    e.1.c. A power density of more than 700 kW/m\3\ of box volume;

    Technical Note: Box volume: the product of three perpendicular
dimensions measured in the following way:
    Length: The length of the crankshaft from front flange to
flywheel face;
    Width: The widest of the following:
    a. The outside dimension from valve cover to valve cover;
    b. The dimensions of the outside edges of the cylinder heads; or
    c. The diameter of the flywheel housing;
    Height: The largest of the following:
    a. The dimension of the crankshaft center-line to the top plane
of the valve cover (or cylinder head) plus twice the stroke; or
    b. The diameter of the flywheel housing.

    e.2. ``Technology'' ``required'' for the ``production'' of
specially designed components, as follows, for high output diesel
engines:
    e.2.a. ``Technology'' ``required'' for the ``production'' of
engine systems having all of the following components employing
ceramics materials controlled by 1C007:
    e.2.a.1. Cylinder liners;
    e.2.a.2. Pistons;
    e.2.a.3. Cylinder heads; and
    e.2.a.4. One or more other components (including exhaust ports,
turbochargers, valve guides, valve assemblies or insulated fuel
injectors);
    e.2.b. ``Technology'' ``required'' for the ``production'' of
turbocharger systems, with single-stage compressors having all of
the following:
    e.2.b.1. Operating at pressure ratios of 4:1 or higher;
    e.2.b.2. A mass flow in the range from 30 to 130 kg per minute;
and
    e.2.b.3. Variable flow area capability within the compressor or
turbine sections;
    e.2.c. ``Technology'' ``required'' for the ``production'' of
fuel injection systems with a specially designed multifuel (e.g.,
diesel or jet fuel) capability covering a viscosity range from
diesel fuel (2.5 cSt at 310.8 K (37.8 deg.C)) down to gasoline fuel
(0.5 cSt at 310.8 K (37.8 deg.C)), having both of the following:
    e.2.c.1. Injection amount in excess of 230 mm<SUP>3</SUP> per
injection per cylinder; and
    e.2.c.2. Specially designed electronic control features for
switching governor characteristics automatically depending on fuel
property to provide the same torque characteristics by using the
appropriate sensors;
    e.3. ``Technology'' ``required'' for the ``development'' or
``production'' of high output diesel engines for solid, gas phase or
liquid film (or combinations thereof) cylinder wall lubrication,
permitting operation to temperatures exceeding 723 K (450 deg.C),
measured on the cylinder wall at the top limit of travel of the top
ring of the piston.
    f. ``Technology'' not otherwise controlled in 9E003.a.1 through
a.12 and currently used in the ``development'', ``production'', or
overhaul of hot section parts and components of civil derivatives of
military engines controlled on the U.S. Munitions List.

9E018  ``Technology'' for the ``development'', ``production'', or
``use'' of equipment controlled by 9A018.

License Requirements

Reason for Control: NS, RS, AT


               Control(s)                         Country Chart

NS applies to entire entry.............  NS Column 1
RS applies to 9A018.a and .b...........  RS Column 2
AT applies to entire entry.............  AT Column 1


License Exceptions

CIV: N/A
TSR: Yes for Australia, Japan, New Zealand, and NATO only

List of Items Controlled

Unit: N/A
Related Controls: N/A
Related Definitions: N/A
Items: The list of items controlled is contained in the ECCN heading

9E101  ``Technology'' according to the General Technology Note for the
``development'' or ``production'' of goods controlled by 9A101, 9A104
to 9A111 or 9A115 to 9A120.

License Requirements

Reason for Control: MT, AT


               Control(s)                         Country Chart

MT applies to entire entry.............  MT Column 1
AT applies to entire entry.............  AT Column 1


License Exceptions

CIV: N/A
TSR: N/A

List of Items Controlled

Unit: N/A
Related Controls: ``Technology'' controlled by 9E101 for items in
9A101.b, 9A104, 9A105, to 9A109, 9A110 that are specially designed
for use in missile systems and subsystems, 9A111, 9A115, and 9A116
to 9A120 are subject to the export licensing authority of the U.S.
Department of State, Office of Defense Trade Controls (see 22 CFR
part 121)
Related Definitions: N/A
Items: The list of items controlled is contained in the ECCN heading

9E102  ``Technology'' according to the General Technology Note for the
``use'' of goods controlled by 9A004 to 9A011, 9A101, 9A104 to 9A111,
9A115 to 9A120, 9B105, 9B106, 9B115, 9B116, 9B117, 9D101 or 9D103.

License Requirements

Reason for Control: MT, AT

[[Page 2555]]


               Control(s)                         Country Chart

MT applies to entire entry.............  MT Column 1
AT applies to entire entry.............  AT Column 1


License Exceptions

CIV: N/A
TSR: N/A

List of Items Controlled

Unit: N/A
Related Controls: (1) For the purpose of this entry, ``use''
``technology'' is limited to items controlled for MT reasons. (2)
``Technology'' controlled by 9E102 for items subject to the export
licensing jurisdiction of the Department of State in 9A004 to 9A011,
9A101.b, 9A104 to 9A109, 9A110 that are specially designed for use
in missile systems and subsystems, 9A111, 9A115, 9A116 to 9A120, and
9D103 are subject to the export licensing authority of the U.S.
Department of State, Office of Defense Trade Controls (see 22 CFR
part 121)
Related Definitions: N/A
Items: The list of items controlled is contained in the ECCN heading

9E990  ``Technology'', n.e.s., for the ``development'' or
``production'' or ``use'' of equipment controlled by 9A990 or 9B990.

License Requirements

Reason for Control: AT


               Control(s)                         Country Chart

AT applies to ``technology'' for         AT Column 1
 equipment under 9A990 and 9B990 except
 9A990.a.
AT applies to ``technology'' for         AT Column 2
 equipment under 9A990.a only.


License Exceptions

CIV: N/A
TSR: N/A

List of Items Controlled

Unit: $ value
Related Controls: N/A
Related Definitions: N/A
Items: The list of items controlled is contained in the ECCN heading

9E991  ``Technology'', for the ``development'', ``production'' or
``use'' of equipment controlled by 9A991 or 9B991.

License Requirements

Reason for Control: AT


               Control(s)                         Country Chart

AT applies to entire entry.............  AT Column 1


License Exceptions

CIV: N/A
TSR: N/A

List of Items Controlled

Unit: $ value
Related Controls: N/A
Related Definitions: N/A
Items: The list of items controlled is contained in the ECCN heading

EAR99  Items subject to the EAR that are not elsewhere specified in
this CCL Category or in any other category in the CCL are designated by
the number EAR99.

    Dated: December 23, 1997.
R. Roger Majak,
Assistant Secretary for Export Administration.
[FR Doc. 98-1 Filed 1-14-98; 8:45 am]
BILLING CODE 3510-33-P
